一、防水卷材不透水儀產品簡介：
防水卷材不透水儀采用電動氣泵加壓，采用電器自動控制加氣加壓，自動保持壓力，為油氈和防水卷材不透水性的檢測、實驗和研究提供了方便的設備。在測試壓力不大于0.6MPa的情況下，可以用本儀器作其它有關材料透氣性或透水性的測定。用于檢測石油瀝青油氈及高分子防水卷材不透水性的儀器.依照GB/T328.8-2007所規定的試驗要求設計制造。
First, the product introduction:
The waterproof membrane impervious instrument adopts electric air pump to pressurize, adopts electric appliance to automatically control the aerated pressure and automatically maintains the pressure, and provides a very convenient equipment for the detection, experiment and research of imperviousness of linoleum and waterproof coiled material. In the case where the test pressure is not more than 0.6 MPa, the instrument can be used for the determination of other materials for gas permeability or water permeability. It is used to test the impermeability of petroleum asphalt felt and polymer waterproof membrane. It is designed and manufactured according to the test requirements specified in GB/T328.8-2007.
二、防水卷材不透水儀使用方法：
★把要試驗的材料剪成3個135mm的圓形或大于135mm的方形試件待用。
★在使用前根據試件的試驗要求把壓力表調整好。
調節方法是：壓力表的玻璃蒙中間有調節旋鈕，他的上限和下限調節定值，需要借助一字螺絲刀。把把上限指針擰到試驗規定的壓力數的位置，下限指針擰到比上限小0.05Mpa的位置，這樣在工作時當壓力達到要求時（上限值）自動停止加壓。當滲漏或透水使壓力下降到一定數值（下限值）氣泵又自動啟動補充壓力。例如：試驗壓力要求0.3Mpa，表殼中間處圈把上限指針撥到表盤的0.3的位置，再用螺絲刀將中間下限指針擰到0.25的位置。
★使用時，先用內六角扳手把三個透水盤的壓圈松開卸下，把注水口的蓋擰開，再把放水閥關嚴，從注水口慢慢注入清水，至容器的2/3處，分別擰開閥門“1"“2"“3"（0為放水閥）中間的進水孔冒出水來，溢滿透水盤為止，然后把注水口蓋擰緊。
★把被測試件，放在透水盤環形膠圈上，再把試件壓板放在被測試件上，擰緊螺絲。
★根據實驗要求設定時間撥碼，設定時間值。
★插上電源插頭，打開啟動開關，氣泵開始往容器內注入壓力氣體，此時加壓指示燈亮。
★到壓力上xian shi自動停止加壓，此時恒壓指示燈亮，按規定時間試驗完成后，擰開放水閥，把水放出卸掉壓力，再松開壓圈取下試件，試驗完畢。
Second, the method of use:
★ Cut the material to be tested into three 135mm round or square specimens larger than 135mm for use.
★ Adjust the pressure gauge according to the test requirements of the test piece before use.
The adjustment method is: the glass of the pressure gauge has an adjustment knob in the middle, and the upper and lower limits are adjusted, and a flat-blade screwdriver is needed. Screw the upper limit hａnd to the position specified by the test. The lower limit hａnd is screwed to a position 0.05 m below the upper limit, so that the pressure is automatically stopped when the pressure reaches the required level (upper limit value) during operation. When the leakage or permeable water causes the pressure to drop to a certain value (lower limit value), the air pump automatically starts the supplementary pressure. For example, the test pressure requires 0.3Mpa, and the upper limit of the case is turned to the position of 0.3 of the dial, and then the middle lower limit pointer is screwed to the position of 0.25 with a screwdriver.
★When using, first use the Allen key to loosen the pressure ring of the three permeable trays, unscrew the cover of the water inlet, and then close the drain valve. Slowly inject the water from the water inlet to the container 2/ At the 3 places, unscrew the water inlet hole in the middle of the valve “1", “2" and “3" (0 is the drain valve), overflow the draining plate, and then tighten the water inlet cap.
★ Place the tested piece on the circular apron of the permeable tray, then place the test piece on the tested part and tighten the screw.
★ Set the time dialing code according to the experimental requirements and set the time value.
★ Plug in the power plug and turn on the start switch. The air pump starts to inject pressure gas into the container, and the pressure indicator lights up.
★ When the pressure upper limit is reached, the pressure is automatically stopped. At this time, the constant pressure indicator light is on. After the test is completed according to the specified time, the water valve is opened, the water is released, the pressure is released, and the pressure ring is released to take off the test piece. The test is completed.
三、防水卷材不透水儀技術參數：
★電源：220V 50HZ
★試驗壓力：0-0.6Mpa
★可試件數：3件（一組）
★試件尺寸：150mm×150mm
★透水盤內徑：Φ92mm
★測試水溫：20℃±5
★外形尺寸：1150x530x1720mm
★ 重量：50kg
Third, technical parameters:
★Power: 220V 50HZ
★ Test pressure: 0-0.6Mpa
★Number of test pieces: 3 pieces (one set)
★ Specimen size: 150mm × 150mm
★ permeable tray inner diameter: Φ92mm
★ Test water temperature: 20 °C ± 5
★Dimensions: 1150x530x1720mm
★ Weight: 50kg
四、防水卷材不透水儀注意事項：
★ 每次試驗完畢，要把透水盤的各個件擦干凈，涂抹防銹油脂。
★ 壓力上不去時，應檢查各部位是否有漏水或漏氣的地方，或者氣泵與容器連接的氣門心是否老化，應及時更換。
Fourth, note:
★ After each test, wipe off the parts of the permeable tray and apply anti-rust grease.
★ When the pressure is not going, check whether there is any leaking or leaking parts in each part, or whether the valve heart connected to the air pump and the container is aging, and should be replaced in time.
會員1.png)
QQ:2568841715
